SABRE SYSTEMS OWB CZ P10F - Outside the Waistband kydex holster

Product detailed description

Kydex holster for CZ P10F for Outside Waist Band Carry.

Like all SABRE SYSTEMS kydex holsters, this holster is compatible with both standard and enlarged controls such as the bolt catch and magazine release button. All of our holsters are Red Dot-ready from the start, regardless of whether the gun comes factory-equipped with Red Dot preparation or you've had it retrofitted. Compatibility with high sights is also a matter of course. Like all our OWB holsters it has a half sweatguard. The holsters have extended ramps for more intuitive loading of the firearm. 

The SABRE SYSTEMS OWB external belt holsters have a five-hole recess on the back for mounting, the holes are identical on the underside of the pistol. These are used to attach any suitable belt loops or loops with a hole spacing of 3/4" (19 mm). For greater variability in the height of the holster and adjustment of the inclination, we multiplied these holes by half the spacing, i.e. 9.5 mm.   

Our OWB belt holsters come standard fitted with Infinity Loops belt loops from the American company MatchPoint for belts up to 1.75" (44.4 mm) wide, i.e. standard tactical duty belts (Blackhawk CQB Rigger's Belt, Helikon UTP Belt, Custom Gear inner belts, etc.) or 1.5" for belts up to 38 mm wide.

Infinity Loops are made from an almost indestructible Tufmax 820 polymer, their middle section is flexible (it can be bent to a right angle without issue) and the loops adapt to fit the circumference of your waist. They offer a wide range of positioning options - if you mount the rear loop facing up and the front loop facing down, you get an ergonomic forward cant of the gun of about 10°. If you mount them the other way around, you get a negative 10° cant. If you mount both facing the same way up, the holster sits flat with no cant, positioned lower on the belt; mounted the opposite way, it sits higher. For even finer tuning, you can use the "every other" holes in the loops and pick the matching position based on the holster's mounting holes. From the factory, we mount the loops in the forward-cant position.  

Infinity Loops will shape themselves to your waist over time, but of course you can also shape them yourself right away. Simply bend the loops to follow the curve of your waist - no need to worry, they won't break; you can bend them almost 180 degrees, pressing them all the way flat against the inside of the holster.

For more information about holsters for OWB carry, visit this article.

The holster has an adjustable retention and a prominent retention point. The pistol goes into the holster smoothly, has minimized friction surfaces, especially on the sides of the bolt, there is little play, which helps to save the finish of the firearm, and locks firmly only after the firearm is fully inserted with a clear and noticeable "click" behind the trigger (in the holster of a holster without a flashlight). When drawing after overcoming the retention point, the gun leaves the holster completely smoothly again. The screw in front of the trigger is used to adjust the retention (for pistols without a flashlight). In the holster of a firearm with a flashlight, the retention point and lock is on the body of the flashlight, depending on the type and model.

After adjusting the inclination and the bolt of the holster, it is necessary to secure the screws against loosening with a suitable agent (e.g. Loctite).

The holster is designed as open in the lower part, which allows dirt to fall freely, such as sand during intensive activities, in an emergency it will also fit a longer firearm model (e.g. Glock 17 in a holster for Glock 19), while the overhanging part of the firearm will protrude from the holster.

The holster is intended only for the given model of firearm, or a combination of firearm and flashlight. A different model of gun or light gun will not fit in the holster or will not be adequately secured. 

When using, observe the safety rules for handling the firearm. Prevent loose parts of clothing or equipment from entering the holster when inserting firearm. Catching them between the holster and the trigger can lead to an unwanted shot and endanger life.  

If dirty, wash the holster from the inside and outside with a stream of running water and dry with a cloth. Do not use solvents or aggressive cleaning agents. 

Do not expose the holster to temperatures higher than 60 °C. Before each use of the holster, check that all screws are tight and ensure that there are no obstacles or foreign objects inside the holster.