SABRE SYSTEMS OWB Glock 19 / 23 / 32 - Outside the Waistband kydex holster

Product detailed description

SABRE SYSTEMS OWB Glock 19 / 23 / 32 - Outside the Waistband kydex holster

The SABRE SYSTEMS OWB line is designed primarily for outside-the-waistband belt carry, where fast access to the firearm, comfort during extended wear, and adjustability are the priorities. That's why SABRE SYSTEMS OWB holsters feature a mounting hole pattern compatible with Infinity Loops belt loops, which allow for a wide range of holster positioning.

Features

• Compatible with standard and extended controls, such as the slide stop and magazine release button.
• Cut for a red dot sight from the ground up, whether the firearm came optics-ready from the factory or was milled/adapted afterward. Also compatible with tall (suppressor-height) sights.
• Half sweatguard (on all our OWB holsters).
• A flared opening for more intuitive holstering.
• Adjustable retention screws and a pronounced retention point. Minimal friction surfaces, especially along the sides of the slide, which helps protect the firearm's finish. The pistol locks in with a clear, audible "click" behind the trigger guard once fully seated (on models without a weapon light), and draws back out just as smoothly once the retention point is overcome.
• We manufacture this holster in separate right-hand and left-hand versions.
• Usually ships within 7 days or sooner.

Mounting & Infinity Loops

SABRE SYSTEMS OWB belt holsters have a mounting hole pattern with five holes on the back panel, with matching holes on the holster's underside. These accept any suitable belt loops or attachments with 3/4" (19 mm) hole spacing. For greater height and cant adjustability, we've added holes at half that spacing as well — 9.5 mm.

We standard-equip our OWB belt holsters with Infinity Loops belt loops made by the American company MatchPoint, sized for belts up to 1.75" (44.4 mm) wide — common tactical belts (Blackhawk CQB Rigger's Belt, Helikon UTP Belt, Custom Gear inner belts, etc.) — or a 1.5" (38 mm) version for narrower belts.

Infinity Loops belt loops are made from a nearly indestructible Tufmax 820 polymer; their center section is flexible (it can be bent to a full right angle), letting the loops conform to your waist. They offer a wide range of positions:

• Rear loop facing up + bottom loop facing down → an ergonomic ~10° forward cant (factory-installed configuration).
• Rear loop facing down + bottom loop facing up → a ~10° negative cant.
• Both loops facing up → a level holster with no cant, sitting lower on the belt.
• Both loops facing down → a level holster with no cant, sitting higher on the belt.

For even finer adjustment, you can use every other hole in the loops and match it to the corresponding mounting hole on the holster.

Infinity Loops belt loops shape themselves to your waist over time, but you can also shape them right away. Simply bend the loops to follow your waist's contour — there's no need to worry, they won't break; you can bend them almost 180°, pressing them flat against the inside of the holster.

For more on choosing an outside-the-waistband holster, see our article Outside-the-Waistband Holsters (OWB).

Compatibility

• If the Parameters section below lists the construction as open-bottom, the holster is open at the bottom — in an emergency, a longer model from the same family will still fit (e.g. a longer Glock 17 in a holster made for the shorter Glock 19), with the extra length protruding from the holster. If the construction is closed-bottom, the holster closes behind the slide, and a firearm longer than the one it's configured for (e.g. fitted with a compensator or a longer barrel) will not seat fully — the holster must not be used with such a firearm, since it won't be properly retained and the trigger won't be fully covered.
• NOTE: this holster is designed for the specified firearm model only, or for the specified firearm-plus-weapon-light combination. A different firearm model, or the firearm fitted with a light, will not fit the holster, or will not be adequately retained in it.

Adjusting Retention

1. Adjust the holster's cant and retention screws as needed.
2. On firearms without a weapon light, fine-tune retention with the screw in front of the trigger guard. On a firearm with a weapon light, the retention point and lock sit on the light's body, depending on its type and model.
3. Once cant and retention are set, it's a good idea to secure the screws against loosening with a suitable thread-locking compound (e.g. Loctite).

Maintenance & Safety

• Safety warning: always follow safe firearm handling practices. Keep loose clothing or gear away from the holster while reholstering. If caught between the holster and the trigger, it can cause an unintentional discharge and endanger life.
• If dirty, rinse the holster inside and out with running water and dry with a cloth. Do not use solvents or harsh cleaning agents.
• Do not expose the holster to temperatures above 60 °C (140 °F).
• Before each use, check that all screws are tight and make sure there's no obstruction or foreign object inside the holster.

FAQ

Do you make this holster for left-handed shooters too?

Yes — we manufacture this holster in separate right-hand and left-hand versions.

How does the Infinity Loops system work?

The loops are made from a nearly indestructible Tufmax 820 polymer and can be bent to conform to your waist. Depending on how you mount them (facing up or down), you get a ~10° forward cant, a ~10° negative cant, or a level holster sitting higher or lower on the belt. Factory-installed, the loops are mounted for a forward cant.

What belt width does this holster fit?

Infinity Loops belt loops are available in two versions — for belts up to 1.75" (44.4 mm) wide, and for belts up to 1.5" (38 mm) wide.

Is this holster compatible with a red dot sight?

Yes, every SABRE SYSTEMS holster is cut for a red dot sight from the factory, whether the firearm came optics-ready or was adapted afterward.

How long does production take?

Usually ships within 7 days or sooner.

Compatible flashlights

This holster is available for the following flashlights:

• GLOCK GTL II (2025)
• Olight PL X
• Streamlight TLR-1 / TLR-1 HL / TLR-1 HP
• Streamlight TLR-1 HL-X
• Streamlight TLR-1 HP-X
• Streamlight TLR-3X (1913)
• Streamlight TLR-7 HL-X
• Streamlight TLR-7A / 7 X
• Streamlight TLR-8 HL-X
• Streamlight TLR-8A / 8X
• Surefire X300 U / T

Parameters

Holster is open bottom.

Also available with a threaded barrel option.

Gun model compatibility

Compatible models:

• Glock 19 Gen 3-6
• Glock 23 Gen 3-4
• Glock 32
• Glock 45

Incompatible models:

• Glock 23 Gen 5