SABRE SYSTEMS PLATFORM CZ P07 and P09 C NOCTURNE - platform holster

Product detailed description

SABRE SYSTEMS PLATFORM CZ P07 and P09 C NOCTURNE - platform holster

SABRE SYSTEMS PLATFORM holsters are designed primarily for dynamic shooting sports, recreational and tactical shooting, and lighter-duty service use, where a second lock beyond the holster's own retention and screw tension isn't required.

Features

• A mounting hole pattern on the back compatible with a wide range of branded accessories: Safariland QLS, Mid-Ride / Low-Ride platforms, MOLLE platforms, belt loops, or Blackhawk!'s CQC / SERPA carriers and other mounting hardware, G-CODE's RTI system (RTI 39 hanger only), or the widely-used, universal Tek-Lok by Blade-Tech. The holster ships without a mounting system by default; one can be purchased separately as an accessory.
• Compatible with standard and extended controls, such as the slide stop and magazine release button.
• Cut for a red dot sight from the ground up, whether the firearm came optics-ready from the factory or was milled/adapted afterward. Also compatible with tall (suppressor-height) sights.
• A flared opening for more intuitive holstering.
• Adjustable retention screws and a pronounced retention point. Minimal friction surfaces, especially along the sides of the slide, which helps protect the firearm's finish. The pistol locks in with a clear, audible "click" behind the trigger guard once fully seated (on models without a weapon light), and draws back out just as smoothly once the retention point is overcome.
• We manufacture this holster in separate right-hand and left-hand versions.
• Usually ships within 7 days or sooner.

For more on choosing a platform-mount holster, see our article Platform-Mount Holsters (PLATFORM).

Compatibility

• If the Parameters section below lists the construction as open-bottom, the holster is open at the bottom — in an emergency, a longer model from the same family will still fit (e.g. a longer Glock 17 in a holster made for the shorter Glock 19), with the extra length protruding from the holster. If the construction is closed-bottom, the holster closes behind the slide, and a firearm longer than the one it's configured for (e.g. fitted with a compensator or a longer barrel) will not seat fully — the holster must not be used with such a firearm, since it won't be properly retained and the trigger won't be fully covered.
• NOTE: this holster is designed for the specified firearm model only, or for the specified firearm-plus-weapon-light combination. A different firearm model, or the firearm fitted with a light, will not fit the holster, or will not be adequately retained in it.

Adjusting Retention

1. Adjust the holster's cant and retention screws as needed.
2. On firearms without a weapon light, fine-tune retention with the screw in front of the trigger guard. On a firearm with a weapon light, the retention point and lock sit on the light's body, depending on its type and model.
3. Once cant and retention are set, secure the screws against loosening with a suitable thread-locking compound (e.g. Loctite).

Maintenance & Safety

• Safety warning: always follow safe firearm handling practices. Keep loose clothing or gear away from the holster while reholstering. If caught between the holster and the trigger, it can cause an unintentional discharge and endanger life.
• If dirty, rinse the holster inside and out with running water and dry with a cloth. Do not use solvents or harsh cleaning agents.
• Do not expose the holster to temperatures above 60 °C (140 °F).
• Before each use, check that all screws are tight and make sure there's no obstruction or foreign object inside the holster.

FAQ

Do you make this holster for left-handed shooters too?

Yes — we manufacture this holster in separate right-hand and left-hand versions.

Is the PLATFORM holster suitable for duty/service use?

The PLATFORM line is designed primarily for dynamic shooting sports, recreational and tactical shooting, and lighter-duty service use, where a second mechanical lock beyond the holster's own retention and screw tension isn't required. For full duty deployment with a Level 2 lock, we recommend the DUTY line.

Can I fit a different or longer firearm in this holster?

In an emergency, a longer model from the same family will fit in open-bottom construction (with the extra length protruding from the holster); the holster is not designed for any firearm model outside the specified family.

Is this holster compatible with a red dot sight?

Yes, every SABRE SYSTEMS holster is cut for a red dot sight from the factory, whether the firearm came optics-ready or was adapted afterward.

Does it come with a mounting system (Safariland, MOLLE, Tek-Lok...)?

No, the holster ships without a mounting system. One can be purchased separately as an optional accessory.

How long does production take?

Usually ships within 7 days or sooner.

Compatible flashlights

This holster is available for the following flashlights:

• Olight PL X
• Streamlight TLR-1 / TLR-1 HL / TLR-1 HP
• Streamlight TLR-1 HL-X
• Streamlight TLR-1 HP-X
• Streamlight TLR-3X (1913)
• Streamlight TLR-7 HL-X
• Streamlight TLR-7A / 7 X
• Streamlight TLR-8 HL-X
• Streamlight TLR-8A / 8X
• Surefire X300 U / T

Parameters

Holster is open bottom.

Also available with a threaded barrel option.

Gun model compatibility

Compatible models:

• CZ P07
• CZ P09C NOCTURNE

Incompatible models:

• CZ P09
• CZ P09F NOCTURNE